sprinter - Firmware for 3d printer

Age	Commit message (Collapse)	Author
2012-02-06	Add pin definition for the Printrboard Rev B --> Thaks to lwalkera	midopple

2012-01-29	Merge commit 'fa63b839c6cbf261f2655e8783bf4745cc9ca513' into SprinterV2	midopple
	Conflicts: Sprinter/Configuration.h
2012-01-29	New Version Sprinter V2	midopple
	- Look Vorward Funktion - - Stepper Control with Timer 1 - SOFT PWM for Extruder heating --> Free Timer 1 - G2 / G3 Command for arc real arc - Baudrate 250 kbaud - M30 Command delete file on SD Card - Text moved to flash to free RAM - M203 Command for Temp debugging
2011-11-28	Revert "Merge pull request #121 from Traumflug/master"	Kliment Yanev
	This reverts commit 11d3281a09e2a2f0ae7c9695f79d2d903c22716b, reversing changes made to f8c17d3b4655ba9b694c407ff174135badb914a5.
2011-11-28	pins.h: allow an ATmega644 (without P).	Markus Hitter

2011-10-29	Define default value for alarm pin	Kliment Yanev

2011-10-28	Moved pins.h footer to the end of the file, fixing teensylu support	Joe Kerman

2011-10-27	Merge branch 'master' of github.com:kliment/Sprinter into experimental	Kliment Yanev
	Conflicts: Sprinter/Configuration.h
2011-10-04	(correct) pin defs for a190usb1286/teensylu	Joe Kerman

2011-09-30	pins.h entry for Teensylu	Joe Kerman

2011-09-25	Edited Sprinter/pins.h via GitHub	rotorit

2011-09-17	Signal an optional ALARM_PIN when reaching MAXTEMP	Alessandro Ranellucci
	Alarm signal can be dismissed by hard-resetting the board or by sending a M42 P23 S0 command (where 23 is the ALARM_PIN)
2011-09-03	Merge branch 'master' into experimental	Kliment Yanev

2011-09-03	Fix missing newline in pins.h that prevents max6675 support from working	Kliment Yanev

2011-08-31	Merge branch 'experimental' of github.com:kliment/Sprinter into experimental	Kliment Yanev

2011-08-31	Merge branch 'master' of github.com:kliment/Sprinter into experimental	Kliment Yanev

2011-08-31	Add temp2 pin define	Kliment Yanev

2011-08-12	Merge pull request #69 from changwoo/master	kliment
	ATmega1284P support
2011-08-09	first revision... had to use the fan pin to control the extruder hot end ↵	rotorit
	heater. meaning.. this setup will not support a bed heat control ..for now... Time will show if I can get the Tip management A/D converter to work... or.. should i get it to work at all???
2011-08-09	typo	rotorit

2011-08-09	Added support for Gen3-pluss and Gen3-Monolithic Electronics	rotorit

2011-08-09	Support Sanguino/Sanguinololu with ATmega1284P	Changwoo Ryu

2011-08-02	Added a list of pins which will be ignored by manual change through M42	blddk

2011-07-18	Added Ramps 1.3 pin assignments for E1 (second extruder) stepper driver	Emery Roth
	This is my first commit…Please don't hurt me if i screw up!
2011-07-06	Documentation fix - delete misleading comment	kliment

2011-07-06	Fix sanguinololu version define	kliment

2011-07-05	Merge branch 'master' of github.com:kliment/Sprinter into refactor	kliment

2011-07-05	Cleaned up configuration. Made a hack so that board versions can be set from ↵	kliment
	configuration.h. Combined thermistor tables. Enabled maxtemp and mintemp by default. Changed case of configuration.h to make it appear first in Arduino IDE
2011-07-04	Merge branch 'experimental'	Joem

2011-07-04	Rename to Sprinter	kliment